Bearing Unit 8 D10 e
0.0.442.09

Bearing Unit 8 D10 e

0.0.442.09

CAD-data bekijken Aan vergelijkingslijst toewijzen Producten vergelijken https://nl-product.item24.com/nl/directlink/pro/44209
Speciale eigenschappen:
item-producten zijn gebaseerd op verschillende modulaire afmetingen en hun bijbehorende systeemroutines. Profielen uit de series 5, 6, 8, 10 en 12 hebben allemaal hun eigen bevestigingsmiddelen in bijbehorende maten nodig. De profielen van serie X komen overeen met de systeemroutine van lijn 8 maar hebben een specifiek plat oppervlak met minimale bochtdiameters waardoor ze ideaal zijn voor het vervaardigen van gesealde constructies.
Onderdelen die aan RoHS voldoen bevatten geen gevaarlijke stoffen zoals lood of cadmium. De EG-richtlijn 2002/95/EG (RoHS 1) stelt beperkingen aan het gebruik van bepaalde stoffen in elektrische en elektronische apparatuur. Dat geldt ook voor batterijen e.d.
Alle materialen zijn geregistreerd in overeenstemming met de REACH-regels. REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) garandeert dat gebruikers over exacte informatie betreffende de soort en eigenschappen van de bedrijfsmiddelen, smeermiddelen enz. beschikken waarmee zij in aanraking kunnen komen.
Leveringseenheid
Schaalbegrenzing
Prijs
1 pce.
≥1
on application

on application

Meer productinformatie

  • Attributen
  • Details
  • Accessoires
  • Tools
  • Downloads
  • Applicatie
  • Classificatie
Bearing Unit 8 D10 e
0.0.442.09

Attributen

Line
line 8
Material
Al, anodized, natural
Delivery unit
1 pce.
Weight
m = 210 g
ESD
ESD-safe = No
Torque, locknut
Mlocknut = 6 Nm
Load Factor, dynamic
C = 4400 N
Load Factor, static
C0 = 2470 N
Bearing Unit 8 D10 e
0.0.442.09

Details

Bolt 8 D10 e
Roller D10
2 Button-Head Screws ISO 7380-M8x16, St, bright zinc-pl.
2 washers ISO 7089 - 8 - 200 HV, bright zinc-plated
4 dowels ISO 8735-D-5m6x16 St, hardened
Notes on Use and Installation
Bearing Units are used in conjunction with a carriage plate for constructing the sliding carriages.
Bearing Units e (eccentric) and c (centric) differ in the geometry of the bolts.
The eccentric bolts can be adjusted subsequently so as to ensure that the guide unit is free from play. Bearing Units should therefore always be used in pairs in both centric and eccentric versions.
The Bearing Units must always be equipped with End Cap and Lubricating Systems in order to prevent premature wear.
If there are undefined loads on the guide unit such as impact loads that could cause movement in the Bearing Units, the Bearing Units will need to be reinforced. You can do this by drilling and pinning (a) the Units in the positions indicated or the areas shown in dark grey.
a = dowel DIN 7979-5x16
If the Bearing Units are to be mounted offset 90°, the fastening and fixing bores must be located in accordance with the specified dimensions or in the dark-grey areas.
Bearing Unit 8 D10 e
0.0.442.09

Accessoires/service

End Cap and Lubricating System 8 D10, black
Leveringseenheid
1 set
Artikelnr.
0.0.442.23
End Cap and Lubricating System 8 D10, grey
Leveringseenheid
1 set
Artikelnr.
0.0.630.01
Bearing Unit 8 D10 e
0.0.442.09

Tools

Pin Spanner 5 D6, 8 D10, black
Leveringseenheid
1 pce.
Artikelnr.
0.0.390.13

Downloads

Technical documentation(1 MB)
Assembly instruction(451 KB)

Applicaties

Machine frame with 3-axis handling - Article EX-01072

This stable machine frame is held together by Angle Brackets and stands firm even when subjected to frequent and rapid movements in three spatial directions.

Meer informatie
PDF CAD Onderdelenlijst Tekening

Applicaties

3-axis handling - Article EX-01078

item linear technology can be used to design highly accurate 3-axis handling systems. Movement along the X axis is controlled by two synchronised KLE 8. Movement along the Y axis is controlled by roller guide 8 D10 with timing-belt drive, while roller guide 8 D14 with timing-belt drive takes care of the Z axis.

Meer informatie
PDF CAD Onderdelenlijst Tekening
Bearing Unit 8 D10 e
0.0.442.09

Classificaties

Classificaties zijn industriële productnormen die naast andere zaken worden gebruikt voor een gestructureerde verwerking in ERP en e-business systemen. Hebt u de classificatiegegevens voor alle producten van item nodig voor uw elektronisch aankoopsysteem? Zo ja, aarzel dan niet en neem contact met ons op.
eCl@ss 11.0
23050702
eCl@ss 4.0
23050702
eCl@ss 4.1
23050702
eCl@ss 5.0
23050702
eCl@ss 5.1
23050702
eCl@ss 6.0.1
23050702
eCl@ss 7.1
23050702
eCl@ss 8.0
23050702
UNSPSC 7.0
31171506
UNSPSC 9.0
31171506
customs tariff number
84832000